![](https://smartkidshub.com/wp-content/uploads/2024/02/Image-1-1-1024x480.jpg)
Review and photos by Torvosaurus, edited by Suspsy
Howdy from wonderful, windy Wyoming! Today we’ll take a look at the Honourable Lead Boiler Suit (HLBS) Tyrannosaurus rex. The model is approximately 8 inches (20 cm) long, but the curve of the neck puts it closer to 9 inches (23 cm) and gives it a 1/52 scale. In that respect, the model is small compared to many dinosaurs offered by other companies. It does, however, fit well with many smaller CollectA figures, as do most HLBS figures. This figure was produced in the late 1980s or early 1990s.
![](https://dinotoyblog.com/wp-content/uploads/2024/02/Image-1-1-1024x480.jpg)
The Tyrannosaurus is in a typical mouth-open roaring pose. The body shape in general is accurate. The legs and tail could use a little more muscle mass, but are not outside the realm of possibility. The arms are supinated, a big leap considering pronated arms were pretty much a given among theropods in the 1990s. I’m not sure if this was intended or if the arms were simply sculpted without regard to their position.
![](https://dinotoyblog.com/wp-content/uploads/2024/02/Image-2-1-1024x623.jpg)
The three-toed feet fit well with the figure, but there are no dew claws. The front arms are too long, but have two fingers, with the shorter claw above the longer one. The length of the head is right at 1/6 of the body length, perfect for Tyrannosaurus. Looking at the face from the front allows the viewer to see that this Tyrannosaurus had excellent stereoscopic vision, and that the upper jaw is U-shaped. There is a nice row of teeth, which appear to be properly sized. The head is a little shrink-wrapped toward the rear of the skull, but becomes less so towards the front.
![](https://dinotoyblog.com/wp-content/uploads/2024/02/Image-3-1-1024x725.jpg)
The skin is covered with scales of varying sizes, giving the Tyrannosaurus a nice texture. The figure shows osteoderms aligned along the back, starting with five large rows and gradually reducing to two smaller rows at the end of the tail. These osteoderms are unknown in tyrannosaurs. The figure lacks lips, and there are also no feathers, which may or may not be to a collector’s tastes, as feathers are not known for Tyrannosaurus rex and the debate over lips in theropods continues.
![](https://dinotoyblog.com/wp-content/uploads/2024/02/Image-4-1-1024x768.jpg)
The model came unpainted and unassembled. The top of the head, the arms, and the legs went on easy, but the tail isn’t quite wide enough for the open space allotted for it. The tail is pinned in place by a 3/8 inch (10 cm) dowel as the opening on the rear of the figure is concave, but the tail surface is flat, leaving only the outside edge for glue. This figure is all white medal. HLBS has started making figures again, but this model is retired and not part of their current line. Occasionally, it can be found on eBay.
![](https://dinotoyblog.com/wp-content/uploads/2024/02/Image-5-1-1024x459.jpg)
Overall, the model is fairly accurate. It is a “big boy” toy, intended for gaming purposes. It is quite heavy, possibly 2.5 pounds (1.2 kg) and not suitable for younger children. This would be a great model for anyone, especially a collector who focuses on tyrannosaurids.
Support the Dinosaur Toy Blog by making dino-purchases through these links to Ebay and Amazon. Disclaimer: links to Ebay.com and Amazon.com on the The Dinosaur Toy Blog are often affiliate links, when you make purchases through these links we may make a commission
Trending Products